View LQH6PPN100M43P_4635393.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type)
Data Sheet
1
Chip Inductor (Chip Coil)
I Dimensions
Power Inductor (Wire Wound Type)
LQH6PP Series (2424 Size)
I Packaging
Code L K
6.00.2 4.30.2 (0.2)
Packaging 180mm Embossed Tape 330mm Embossed Tape
Minimum Quantity 250 1500
6.00.2
6.00.2
1.650.2
1.650.2
(in mm)
I Rated Value (p: packaging code)
Part Number LQH6PPN1R0N43p LQH6PPN1R5N43p LQH6PPN2R2N43p LQH6PPN3R3N43p LQH6PPN4R7M43p LQH6PPN6R8M43p LQH6PPN100M43P LQH6PPN150M43p LQH6PPN220M43p LQH6PPN330M43p LQH6PPN470M43p LQH6PPN680M43p LQH6PPN101M43p Inductance 1.0H30% 1.5H30% 2.2H30% 3.3H30% 4.7H20% 6.8H20% 10H20% 15H20% 22H20% 33H20% 47H20% 68H20% 100H20% Inductance Allowable DC Current Test Frequency (Based on Temperature Rise) 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 4.30A 4.15A 4.10A 3.80A 3.20A 2.85A 2.60A 2.20A 1.55A 1.29A 1.10A 1.00A 0.80A Allowable DC Current (Based on Inductance Change) 7.50A 6.50A 5.60A 4.50A 4.00A 3.20A 2.60A 2.20A 1.70A 1.60A 1.25A 1.10A 0.92A DC Resistance 0.009ohm30% 0.010ohm30% 0.014ohm30% 0.016ohm30% 0.020ohm30% 0.028ohm30% 0.044ohm30% 0.065ohm30% 0.108ohm30% 0.137ohm30% 0.230ohm30% 0.289ohm30% 0.436ohm30% Self Resonance Frequency (min.) 110MHz 60MHz 30MHz 30MHz 25MHz 20MHz 15MHz 10MHz 10MHz 6MHz 6MHz 5MHz 3MHz Class of Magnetic Shield Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin Magnetic shield of magnetic powder in resin
Operating Temperature Range: -40 to +85C Only for reflow soldering.
I Notice (Allowable DC Current)
When Allowable DC Current is applied to the Products, self-generation of heat will rise to 40C or less. When Allowable DC Current is applied to the Products, Inductance will be within +-30% of nominal Inductance value.
Continued on the following page.
o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2010.4.30
http://www.murata.com/
Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type)
Data Sheet
Continued from the preceding page.
2
I Inductance-Frequency Characteristics (Typ.)
1000 100H 68H 47H 33H 22H 15H 10H 6.8H 4.7H 3.3H 2.2H 1.5H 1.0H 1
I Inductance-Current Characteristics (Typ.)
100 100H 68H 47H 33H 22H 15H 10H 6.8H 4.7H 3.3H 2.2H 1.5H 1.0H
100 Inductance (H)
Inductance (H)
10
10
1
0.1 0.1
1
10 Frequency (MHz)
100
1000
0.1 10
100 DC Current (mA)
1000
10000
I Temperature Rise Characteristics (Typ.)
40 100H 68H 47H 30
Temperature Rise (C)
15H 22H
10H 6.8H
4.7H
33H
20
10
3.3H 2.2H 1.5H 1.0H
0 0 1000 2000 3000 4000 5000
DC Current (mA)
I !Caution/Notice
!Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use.
o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2010.4.30
http://www.murata.com/

▲Up To Search▲

Price & Availability of LQH6PPN100M43P

	To Download LQH6PPN100M43P Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .